比如说你说到展柜，展柜摇晃，面上玻璃高低不平，这个这种问题是怎么造成的呢？

玻璃高低不平，一个可能现在玻璃都是用的是10mm的面玻，然后面玻都会去做钢化。做了钢化，尤其是那些弧形玻璃比较大，然后高低不平这边翘起来，那边矮下去。所以展柜面上就会出现一个高低不平的情况。

但是玻璃做钢化会安全，现在包括我们这个小区的那种窗户玻璃都是做钢化，我们展柜玻璃也都是做钢化。钢化是要进炉子烧高温，自然会发生一些化学变化，你不做钢化，肯定玻璃面就比较平，它就不会有变化，这也证明了我们自己，我们都是实打实的给客户钢化，钢化的比较安全。

还有一个情况，就是比如说不锈钢的展柜，我们的那个玻璃都是放在一个灯罩上面的嘛，灯罩也是手工焊的，会有1mm-2mm的误差，所以呢，导致这个玻璃它可能也有一点翘，然后翘上加翘，就很多做弧形柜会出现这种情况。我也出现了两次，我们现在也是找原因去改善它，坚决不出现第三次。

我们有2个改变方法：

1）玻璃薄一点，由10mm改为8mm，它的承重各方面也够的都是OK，然后面上也看不出来，我们就用8mm的玻璃去做钢化，8mm比10mm少了2mm嘛，就有一点余地，就正好它跟面上是平齐的，就不会说翘起来。

2）玻璃不钢化，就用10mm的夹胶玻璃，也能达到10厘厚度的效果，因为两层啊，所以它也不容易脆，然后夹胶玻璃呢，如果有破损，它也不会像我们以前那种单层玻璃那样子碎的满地，所以呢，这就是在玻璃上做的一些改进。

3）灯罩结构改进，在不锈钢框架上面做的一个改进的方法，我也是跟师傅讨论这个结构怎么做，就是我们还是要把这个精密度啊，紧配合度做的要更加紧密一点。就是每次做，我们都用钢尺去量，确定预留好所有的位置都一致，因为弧形很大，它有时候就那边可能预留了10mm，这边呢可能就预留了9mm，中间有可能预留了8mm，所以我们现在就是对工人的这道工序要把一下关，就是全部预留好一样的尺寸，大家都是10mm，或者大家都是12mm，这样子做出来就不会说高低不平了。

上面3种方法都要在实际生产中试验一下确保达到最好的制作效果。

Let me teach you how to check the quality of the glass in my kind of display cabinet.

For example, when you mentioned that the display cabinet wobbles and the glass surface is uneven, what could be the reasons behind it?

One possible reason for the uneven glass surface is that we often use 10mm thick tempered glass for the front panel. Tempered glass, especially for large curved pieces, can sometimes exhibit warping or unevenness due to the tempering process. So, you might see some parts of the glass surface lifted up while others are lower down, resulting in an uneven appearance.

But tempered glass is necessary for safety reasons. Even the window glass in our neighborhood and the glass in our display cabinets are tempered. The tempering process involves heating the glass to a high temperature, which naturally causes some chemical changes. If we didn't temper the glass, it would be flatter, but it wouldn't be as safe. This proves that we genuinely temper our glass for our customers' safety.

Another factor is that for stainless steel display cabinets, the glass is usually placed on a light cover, which is handmade and may have a 1mm to 2mm error. This can contribute to the glass warping, and when combined with the warping from tempering, it's more likely to cause unevenness, especially in curved cabinets. We've encountered this issue twice and are actively working on improvements to prevent it from happening again.

Here are two solutions we're considering:

Use thinner glass, switching from 10mm to 8mm. This thickness is still sufficient for bearing weight and won't be noticeable visually. The 8mm glass can be tempered, and with the reduced thickness, it's more likely to be flush with the surface, avoiding warping.

Instead of tempered glass, use 10mm thick laminated glass. It provides the same thickness effect as two layers of glass, making it less prone to breaking. And if it does break, it won't shatter like regular single-layer glass, ensuring safety.

The improvement of the lampshade structure, an improvement method made on the stainless steel frame, I also discussed with the master how to do this structure, that is, we still have to make this precision ah, and the tightness of the fit should be made a little tighter. It is every time we do it, we use a steel ruler to measure, to make sure that all the positions are the same, because the arc is very large, it sometimes may be reserved for 10mm, this side may be reserved for 9mm, and there may be 8mm in the middle, so we are now for the workers' process to close, that is, all the same size is reserved, everyone is 10mm, or everyone is 12mm, so that it will not be said to be uneven.

We'll test all three methods in actual production to ensure the best results.

我是展柜大小姐章娅妮，来自东莞鑫峰展柜厂，30年来我们厂只做类似于卡地亚珠宝这样的奢侈品展柜和道具。

100多个国内外品牌授权我们厂制作展柜和道具，虽然我们贵一点，但是品质堪比卡地亚。

既能做钟表、珠宝、博物馆等展柜，又能做陈列道具的工厂，这样的工厂，在国内没有第二家。

我已经用自己的姓名“章娅妮”注册了展柜品牌，这代表了我此生不转行。

做了不称心的展柜，应该来鑫峰厂试试。

手机/微信：17688026138

联系人：章娅妮

地址：中国广东省东莞市企石镇永发工业区环企大道42号之一

I am Ms. Zhang Yani, from Dongguan Xinfeng Showcase Factory. For 30 years, our factory has only made luxury showcase and props similar to Cartier jewelry.

More than 100 domestic and foreign brands authorize our factory to make display cases and props, although we are a little more expensive, but the quality is comparable to Cartier.

Both can do watches, jewelry, museums and other display cases, but also can do display props factory, such a factory, there is no second in the country.

I have registered the showcase brand with my own name "Zhang Yani", which means that I will not change my career in this life.

Do not satisfactory display case, should come to Xinfeng factory to try.

Tel/wechat: 17688026138

Contact: Zhang Yani

Add: No. 42 Huanqi Road, Yongfa Industrial Zone, Qishi Town, Dongguan City, Guangdong Province，China